Let's talk!

How for making Safer, Superior Cuts on the Miter Saw

  • click to rate

    Our professional, Jerome Worm, continues to be using a miter noticed each day for New Miter Saw Deals 30 decades. He describes how to find the most out of the miter saw and shared guidelines on how to Minimize smaller pieces, minimize tear-outs and, most critical, how to get it done all safely and securely.

    Clean up, Risk-free Miter Noticed Cuts

    Dropping the miter saw blade in the workpiece far too fast is perilous and may probable end in a tough Lower or splintered wood. This is very true if you’re cutting thin, narrow items. Give the motor a couple john witherspoon Miter saw of excess milliseconds to succeed in whole velocity, then reduced the blade little by little as you cut.

    Use a Sacrificial Fence

    To prevent launching tiny parts across the place, utilize a sacrificial fence. Build a two-piece fence for very small content like this cove molding (left). Or perhaps use a scrap board to again up modest cutoffs (right). Keep the noticed down at the conclusion of the Lower and Allow the blade come to a complete prevent.

    Have a Miter Noticed by the Base

    Miter saws are large and uncomfortable to hold. Some saws have handles close to the best so you're able to lug them just like a suitcase, but get to the behavior of carrying them by The bottom instead. It’s less difficult on the back again and won’t defeat up the facet of your respective leg. It’s also simpler to get as a result of door openings without banging up the trim.

    Send out Miter Saw Dust Down

    Managing dust designed by a miter observed is notoriously difficult. The gathering bags do little, and Even though you hook up a vacuum, dust continues to be planning to fly. Our pro replaced his bag by having an ABS plumbing elbow that in shape snugly on to the dust chute. It doesn’t Command many of the dust, nevertheless it sends a great part of it to the ground rather than all over. Dust chutes change in size, so evaluate yours just before heading towards the hardware retailer. The sole surefire method to completely keep away from dust indoors is to try and do your chopping exterior.

    Mark a Guideline on the Miter Noticed Base

    Listed here’s a quick solution to Lower lots of components to a similar length: Position the 1st one and afterwards mark The situation of the end about the observed foundation with a pencil. Now there is a guideline for the rest of your sections. This technique might not be as exact as a cease block, but in some cases perfection is pointless. The pencil mark conveniently rubs off if you’re carried out.

    Constantly Have on Listening to Protection

    If you asked our Professional why he never wore Listening to security when he was younger, he would probably provide you with a blank stare Unless of course he’s putting on his hearing aids. Miter saws are loud and will destruction your ears Except you safeguard them. Our Professional will be the very first to inform you that Listening to loss is no joke!

    Make Micro-Adjustments

    Right here’s a tip when you must shave off only a little bit: Decrease the blade when it’s not spinning, and force the fabric restricted up in opposition to the human body of your blade. Get a company grip on the fabric and lift the blade. Next, fan the flames of the noticed and lower the blade yet again. Because the enamel of the blade are a little wider than your body, you’ll find yourself shaving off only a hair.

    Screw Guides On to the Miter Saw Base

    Clamping down A short lived information tends to make slicing crown molding a good deal a lot easier, but often the clamps are tricky to set up because of the irregular form of most miter noticed bases. Clamps also can get in how once you’re switching the angle of the Slash. Don’t be afraid to screw down a manual right into the base of the saw. A small gap will not be planning to impact the best way the noticed performs. Self-tapping screws operate excellent in bases product of aluminum: Just be sure you placement the stop so it doesn’t interfere after you’re changing angles. Install a couple screws on either side If your guidebook can get Minimize in 50 percent, and help you save your guides so You should utilize precisely the same screw holes following time.

    In no way Cross Your Arms

    Sorry, lefties, but most miter saws are suitable for ideal-handed users, that means the observed is operated with the ideal hand and the material held down While using the left. But sometimes the fabric will have to be held down on the appropriate facet of the blade. On People situations, it’s tempting to continue to make use of your ideal hand to work the saw, but doing so will lead to your still left hand to cross in front of the path of your blade—that’s bad. It can sense Unusual, but in this example, make use of your remaining hand to function the observed and also your proper to secure the fabric. Our professional is familiar with carpenters who have disregarded this recommendation and also have the scars on their arms to confirm it.

    Slash Vast Boards With the most beneficial Facet Down

    Splinters and tear-outs arise the place the blade breaks from the Wooden. That’s The underside facet when plunge-chopping slim boards, so it’s greatest to chop slim boards With all the “display” side facial john witherspoon Miter saw deals area up. But after you’re slicing broader product on the sliding observed, you’ll pull the blade toward you, decrease the blade and after that push it ahead as you narrow. In that method, splintering will occur on the very best of the board, so Reduce Along with the board facial area down.