Vane Pump Manufacturers -Common Faults Of Vane Pump: Emergency Measures
In the process of using vane pump, it will break down because of service life, lack of regular maintenance and improper operation. When we meet some normal conditions, what methods should we adopt to deal with them? The following vane
pump manufacturer for some common failures, to teach you how to take emergency measures, in the face of serious emergencies, should immediately stop, in order to avoid causing more serious harm.
One: Jian Xiu
In the process of vane pump operation or driving, if it suddenly breaks down, a simple repair method should be adopted so that it can run or operate reliably. Connecting rod bearing damaged, need to replace accessories, if not for the time being, but also need the work of the meter, you can first use solder tinning, so that it can work for a short period of time.
Two: plugging
If the pump is used for a long time, it will cause oil leakage, water leakage and air leakage because of its service life or operation reasons. Emergency plugging and timely shutdown can prevent more damage. Once this happens, epoxy resin can be used to patch or soap, emergency plugging. If there are perforations, they can be served with corks and tied with wire or rope when necessary. If oil leakage occurs due to loosening of pipe joints, it can be tightened by wrapping 3-5 circles of raw rubber tape with random tape around the thread. Contact maintenance personnel in time for timely maintenance.
Three: change parts
In daily life, the market should be equipped with small parts of pumps, such as screws, oil seals, seals, etc. When oil leakage occurs, it can be repaired in time.
Four: dismantling
Without affecting the operation of vane pumps, components that are temporarily unused and damaged can be removed. Some parts can still be used in emergencies after being disassembled and repaired. For example: the bearing of the pump is uneven wear and tear, it can be grinded flat and continue to use.
Five: short circuit
If a component in the hydraulic system or control circuit of the pump is damaged and can not be repaired or replaced without spare parts, if the use permits, it can be considered to be short-circuit connected for emergency use. However, it can not be used for a long time, because the heat of the middle circuit is often increased after short circuit connection, and other circuit components may be burned down. When conditions permit, damaged components must be replaced immediately in order to prevent new faults.
Six: Supplement
When the oil pipe of the pump breaks down, if there is no replacement of the spare pipe, plastic rubber pipe can be used to connect for temporary use.
Seventh: Suspension of use
When the vane pump is in operation or running, if the circuit or hydraulic system is damaged, the damaged part of the vane pump can be disconnected and not used for the time being. If the conductor of the engine starting system is discharged by iron, which cannot be ruled out for a moment, the positive pole can be suspended and cut off, and only the ignition system can be supplied with power for emergency treatment. If one of the parallel branch loops of the hydraulic system fails, the oil intake pipe can be removed and sealed with a plug. In this way, the other branch loops can continue to work and be repaired in time when the operation is completed.
Eight: substitution
When a part of vane pump is damaged and can not work, it can be replaced by other parts which do not affect the work temporarily on the vehicle or parts made from local materials. However, this maintenance method makes the performance of construction machinery recover poorly, and is usually used only in its no-load operation.
As a professional Vane Pump Manufacturers and Vane Pump Suppliers in China, Taizhou Yongheng Hydraulic Machinery Co , Ltd . can provide you with high quality products and services. Eternal Hydraulic is committed to becoming a global one-stop shop for hydraulic products, with professional hydraulic solutions and high-quality products to meet the needs of each customer. The company firmly believes that "only the best can satisfy the best" and becomes the preferred choice of hydraulic components for all customers around the world.
https://www.xjetl.com
In the process of using vane pump, it will break down because of service life, lack of regular maintenance and improper operation. When we meet some normal conditions, what methods should we adopt to deal with them? The following vane
pump manufacturer for some common failures, to teach you how to take emergency measures, in the face of serious emergencies, should immediately stop, in order to avoid causing more serious harm.
One: Jian Xiu
In the process of vane pump operation or driving, if it suddenly breaks down, a simple repair method should be adopted so that it can run or operate reliably. Connecting rod bearing damaged, need to replace accessories, if not for the time being, but also need the work of the meter, you can first use solder tinning, so that it can work for a short period of time.
Two: plugging
If the pump is used for a long time, it will cause oil leakage, water leakage and air leakage because of its service life or operation reasons. Emergency plugging and timely shutdown can prevent more damage. Once this happens, epoxy resin can be used to patch or soap, emergency plugging. If there are perforations, they can be served with corks and tied with wire or rope when necessary. If oil leakage occurs due to loosening of pipe joints, it can be tightened by wrapping 3-5 circles of raw rubber tape with random tape around the thread. Contact maintenance personnel in time for timely maintenance.
Three: change parts
In daily life, the market should be equipped with small parts of pumps, such as screws, oil seals, seals, etc. When oil leakage occurs, it can be repaired in time.
Four: dismantling
Without affecting the operation of vane pumps, components that are temporarily unused and damaged can be removed. Some parts can still be used in emergencies after being disassembled and repaired. For example: the bearing of the pump is uneven wear and tear, it can be grinded flat and continue to use.
Five: short circuit
If a component in the hydraulic system or control circuit of the pump is damaged and can not be repaired or replaced without spare parts, if the use permits, it can be considered to be short-circuit connected for emergency use. However, it can not be used for a long time, because the heat of the middle circuit is often increased after short circuit connection, and other circuit components may be burned down. When conditions permit, damaged components must be replaced immediately in order to prevent new faults.
Six: Supplement
When the oil pipe of the pump breaks down, if there is no replacement of the spare pipe, plastic rubber pipe can be used to connect for temporary use.
Seventh: Suspension of use
When the vane pump is in operation or running, if the circuit or hydraulic system is damaged, the damaged part of the vane pump can be disconnected and not used for the time being. If the conductor of the engine starting system is discharged by iron, which cannot be ruled out for a moment, the positive pole can be suspended and cut off, and only the ignition system can be supplied with power for emergency treatment. If one of the parallel branch loops of the hydraulic system fails, the oil intake pipe can be removed and sealed with a plug. In this way, the other branch loops can continue to work and be repaired in time when the operation is completed.
Eight: substitution
When a part of vane pump is damaged and can not work, it can be replaced by other parts which do not affect the work temporarily on the vehicle or parts made from local materials. However, this maintenance method makes the performance of construction machinery recover poorly, and is usually used only in its no-load operation.
As a professional Vane Pump Manufacturers and Vane Pump Suppliers in China, Taizhou Yongheng Hydraulic Machinery Co , Ltd . can provide you with high quality products and services. Eternal Hydraulic is committed to becoming a global one-stop shop for hydraulic products, with professional hydraulic solutions and high-quality products to meet the needs of each customer. The company firmly believes that "only the best can satisfy the best" and becomes the preferred choice of hydraulic components for all customers around the world.
https://www.xjetl.com